Mb991502 Scan Tool Mut Ii. I. Turn the ignition switch to the "ON" position. DIAGN
I. Turn the ignition switch to the "ON" position. DIAGNOSTIC BY DIAGNOSTIC TEST MODE II (INCREASED SENSITIVITY) Required Special Tool: MB991502: Scan Tool (MUT-II) Pinin uses MUT II system which is OBD II equivalent. CAUTION: To prevent damage to scan tool MB991502, always turn the ignition ENCRYPTED CODE REGISTRATION METHOD Required Special Tool: MB991502: Scan Tool (MUT-II) CAUTION Since the registration of encrypted codes occurs after all previously registered codes have MB991502: Scan Tool (MUT-II) NOTE: The standard idling speed has been adjusted with the speed adjusting screw (SAS), by the manufacturer There should be no need for readjustment Required Special Tool: MB991502: Scan Tool (MUT-II) • 1. I wonder if it comes with the ROM packI tried calling my dealer and they MB991502 AC000077AB CAUTION To prevent damage to scan tool MB991502, always turn the ignition switch to the "LOCK" (OFF) position before con-necting or disconnecting scan tool MB991502. But of course, MB991502: Scan Tool (MUT- II) CAUTION: To prevent damage to scan tool MB991502, always turn the ignition switch to "LOCK" (OFF) position before connecting or disconnecting scan tool MB991502. Using scan tool MB991502, read the A/T diagnostic trouble code (DTC). DIAGNOSIS Required Special Tools: MB991502: Scan Tool (MUT-II) MB991958: Scan Tool (MUT-III Sub Assembly) MB991824: V. (1) Connect scan tool MB991502 to the Inspection Using Scan Tool MB991502 Data List Required Special Tool: - MB991502: Scan Tool (MUT-II) CAUTION: To prevent damage to scan tool MB991502, always turn the ignition switch to the I'm not sure what he was looking @ in the FSM but the MUT-II is required for most ECU stuff. MB991502: Scan Tool (MUT-II) NOTE: The standard idling speed has been adjusted with the speed adjusting screw (SAS), by the manufacturer There should be no need for Using scan tool MB991502, check data list item 12: Volume Air Flow Sensor. NOTE: When mode II is selected with MUT-II, the Service Engine Soon/ Malfunction Indicator Lamp will light when the engine control module (ECM) or powertrain control module (PCM) first detects the 52-SPECIAL TOOL (S)SPECIAL TOOLS I verified this just last week with two dealerships as I and a contingent of owners attempted to puchase a MUT-II scanner for the programming of a datalogger. ) (A maximum of eight different ignition key can be registered. Before inspection, set vehicles to the following conditions: - Engine coolant Idle Speed: Adjustments BASIC IDLE SPEED ADJUSTMENT Required Special Tool: - MB991502: Scan Tool (MUT-II) NOTE: The standard idle speed has been adjusted with the speed adjusting screw Required Special Tool: MB991502: Scan Tool (MUT-II) Before inspection, set vehicles in the following condition: Engine coolant temperature: 80 95 C (176 203 MB991502: Scan Tool (MUT-II) NOTE: The standard idle speed has been adjusted with the speed adjusting screw (SAS), by the manufacturer, and there should be no need for readjustment. MB991827: USB Cable MB991911: Main Harness B Turn the ignition switch off before connecting or disconnecting the scan tool. Before inspection, set vehicles in the following condition: Engine coolant temperature: 80 95 C (176 203 • − Lights ° − ° and all 9. Using scan Install the assembled fuel pressure measurement tools between the fuel rail and the high-pressure fuel hose. Read the DTC. Disconnect scan tool MB991502 from the data link connector. If your car has faulty sensors, and is displaying a Check Engine Light (CEL) on your dashboard, you can use Evo Scan to read and identify Diagnostic Trouble Codes (DTCs) You will be able to Read and To prevent damage to scan tool MB991502, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991502. ) Moreover, when the immobilizer-ECU has been replaced, you will need to use scan tool MB991502 to register the immobilizer-ECU and input Ignition Timing: Testing and Inspection IGNITION TIMING CHECK Required Special Tool: - MB991502: Scan Tool (MUT-II) 1. Unless he is trying to just Connect scan tool MB991502 to the data link connector. CAUTION To prevent damage to scan tool MB991502, always turn the ignition switch to the "LOCK" (OFF) position before I've been wondering what the Mitsubishi MUT scan tool can do that the Datalogger can't? Obviously there's the graphing functions offered by the TMO, but surely there's some major Inspection Using Scan Tool MB991502 Data List Required Special Tool: - MB991502: Scan Tool (MUT-II) CAUTION: To prevent damage to scan tool MB991502, always turn the ignition switch to the Retrieving TCL Diagnostic Trouble Codes USING SCAN TOOL MB991502 Required Special Tool: • MB991502: Scan Tool (MUT-II) 16 PIN MB991502 AC001252AF CAUTION STEP 1. (Refer to P. I want to purchase the scan tool (MFI trobbleshoot scan tool) part # mb991502. 2. Part #: MB991502 Description: MUT-II Sub Assembly Mitsubishi MUT-II diagnostic tool is an electronic control box that plugs into FUEL PRESSURE TEST Required Special Tools: MB991502: Scan Tool (MUT-II) MB991637: Fuel Pressure Gauge Set MD998709: Adaptor Hose MD998742: Hose Adaptor Just in case you’re wondering, our list of Mitsubishi OBD scanners are not for simple or entry level OBD code readers. Turn the ignition switch to the "LOCK" (OFF) position. NOTE: When scan tool MB991502 is connected, the diagnostic test mode control terminal should be grounded. I think its required for calibrating a few of the engine sensors. On the contrary, this list is for professional diagnostic Scan Tools that are designed to DIAGNOSIS Required Special Tools: MB991502: Scan Tool (MUT-II) MB991958: Scan Tool (MUT-III Sub Assembly) MB991824: V. CAUTION: To prevent damage to scan tool MB991502, always turn the ignition switch to the "LOCK" (OFF ) position before GENERATOR DRIVE BELT TENSION CHECK < When using scan tool MB991502> Required Special Tools: • MB991502: Scan Tool (MUT-II) • MB991668: Belt Tension Meter Set Required Special Tools: MB991502: Scan Tool (MUT-II) MB991668: Belt Tension Meter Set Check the drive belt tension. 11A-26. 1. Connect the scan tool (MUT-ll) to the data link connector. C. MB991827: USB Cable MB991911: Main Harness B 1. Connect scan tool MB991502 to the data link connector (16-pin). Connect the special tool (belt tension meter set) to the scan .
